Carpet Cleaning The Green Way – Some Solutions

It doesn’t matter the carpet that you have—it will get stained some day if it already hasn’t. There are professionals in the carpet-cleaning field that can aid you to have your carpet looking spotless once again, but they tend to be on the expensive side and use harmful chemicals to get the job done. Also, there are carpet-cleaning products in stores that are on the affordable side, but they contain many harmful ingredients, some which have been noted to be dangerous. This can put one in a tricky situation: Do you hire a costly professional that uses toxic chemicals or just opt to buy dangerous solutions at a store? How about you do neither and just opt to take the organic route so that you can have peace of mind in every aspect. The following are five ways in which you can ensure a great green carpet cleaning.

How Much Does Hiring a Plumber Really Cost?

There are many different jobs that a plumber can carry out for you. They can install piping and make any repairs that are needed to existing pipes, remove blockages from drains and perform vital services in bathroom and kitchen remodelling.

There may be some aspects of plumbing that you can carry out yourself, but for any major work, it is usually a good idea to use the services of a professional.

The charge for a professional plumber will either be worked out as a flat fee for a particular job or as an hourly rate. There are also many other factors that will affect how much you will pay for a plumber. This can include things such as the experience of the plumber and the work that will be involved.


The charge for labor will vary between plumbers but will usually be in the region of $45 to $65. This will not usually include fees for servicing or inspection.

Flat Fees

The typical fees that you can expect to pay for a range of different services are listed below. These prices will apply if you are charged a flat fee.

Drain Cleaning You could be charged anywhere between $100 and $300 for a drain cleaning service, depending on how difficult it is to clear the blockage. An additional $50 to $100 may also be payable for servicing and inspection.

Main Water Line Installation – If you need a copper water line installed that is around six foot in length then you should expect to pay between $1500 and $2000.

Appliance Installation – A plumber will be able to install many kitchen appliances such as washing machines and dishwashers, and this service will cost between $50 and $200.

Leak Repair – The price of a leak repair depends largely on how difficult the leak is to access and will usually be between $100 and $250.

Piping Installation – There are so many different factors that influence the cost of installing pipes that it is tough to give a ballpark figure. Installing pipes in kitchens is usually a more expensive job than bathroom piping because the room is bigger. This means that more piping may be needed and the job is likely to take longer to complete. If additional materials are needed for the job, then you may have to pay for this yourself. There will also be additional charges if there is old piping that needs removing.

Sump Pump Installation- A sump pump will be necessary to take water away from the foundations of your building. The cost of installing a sump pump can be between $1000 and $3000. This does not include the cost of the sump pump itself, and this can cost up to $400.

Water Heater Installation – to ensure that your water heater is installed correctly and safely, the work needs to be done by a professional plumber. The labor cost for installing a water heater can be as much as $1500, and you are looking at the same amount again for an electric heater. If you choose to have a gas water heater installed, then this will cost in the region of $800.

Cost Of Improvement And Enhancement Works

The installation of a sauna that is big enough for four people will cost between $2400 and $3200 which includes the cost of the sauna.

If you need a propane tank installing by a plumber, then this will cost $100.

It will cost $1900 to install a five-foot bathtub including the bathtub.

A solar water heater will need to be installed professionally and can cost between $6000 and $17000.

If you want a sprinkler system installed in your garden, then this will cost between $1500 and $2500.

Copper piping is considered to be one of the best choices for your property, but it is more expensive than other types of piping.

Additional Costs To Consider

If you go for a cheaper model of water heater, then this may not be the most efficient model which could mean your energy bills would be higher.

If you need to call a plumber out in an emergency, then you could expect to pay an additional rate of between $50 and $75 on top of what they would normally charge.

It is not usually a long job to clean drains, but problems can occur if the sewer has collapsed and this will also mean that extra costs are incurred.

Leaks will be cheaper to fix if they are located near to a fixture such as a sink.

A sump pump that is on a pedestal will be cheaper to install than one that is submersible.

This article is just one of many from Whocutthecheez and plumber Port CoquitlamFind out more in our other articles and find them here on our Google Maps as well!

5 Steps to Mold Remediation

Mold is a problem most homeowners have to deal with from time to time. It was a menace a few years ago, and now its effects have reduced due to effective methods used and awareness among homeowners over the years. With safety being a priority, you are supposed to know these two things about mold. You should prevent mold at first by doing the right things, and when you face it, you should take not hesitate to take care of it. You should ensure that your warranty team follows mold remediation process when handling mold

The following steps can help remediating mold problems:

Step 1: Learn about the moisture

Ideally, all moisture growth is facilitated by water or moisture, and hence you should be knowledgeable about moisture in your home. In fact, assessing the growth of mold involves more than just looking for what is growing visibly on walls or corners of your house because they can grow under or around the walls or corners before they become visible.

Therefore, you should first understand that mold growth is catalyzed
By moisture and then know the sources of moisture or water in your home. This knowledge will help your warranty representative locate the source of moisture in your home and hence locate the source of mold growth to solve the problem once and for all. Even if you keep on clearing the mold on the ground without knowing the source, you won’t be able to eradicate mold for good. Therefore, be a master of moisture to be able to deal with mold.

Step 2: Keep records of mold problems and have a remediation plan

You should document the mold situation in writing or take photos and videos before you embark on remediation. This documented information is very helpful to your warranty team supervisor because it will help him or her develop an effective remediation plan to eradicate the molds for good. A well-documented information will help your warranty team in:

• Approximating the time needed to complete the work
• Determine when to start working on the molds depending on severity
• Knowing whether there are any testing procedures to be done
• Knowing if they will have to relocate the occupants temporarily to deal with the problem
• Choosing who will do the remediation

In the long run, documentation can help your warranty company experts understand more about molds e.g. common species, mode of reproduction and growth to be able to help more home owners.

Step 3: Calculate contamination extent before you start remediation

Since mold growth may be extent, you need to know the extent of mold contamination before you start working. These calculations will help you determine how you will approach mold removal and clean up because you will be having a rough figure of their severity and expanse of growth. Normally, the main aim of mold remediation is to clean up mold growing areas in a home to avoid exposing home owners to a significant amount of mold which would eventually cause health problems. This is only possible if you contamination is calculated to know how you are going to deal with it.

Due to widespread mold problems, The New York City Department of Health (NYC DOH) has developed guidelines to be used in cleaning up mold contamination. The guidelines are used in construction industry to prevent mold growth. Based on the square footage of the mold growth or based on whether mold is located within the HVAC system, these guidelines recommend six (6) levels of mold remediation. These guidelines are widely used in construction industries to reduce mold growth. You can, therefore, calculate the remediation level needed as per the NYC DOH guidelines.

Step 4: Remedy mold contamination

Remediation involves cleaning up of existing molds while still avoiding exposing oneself or the home owners to the molds.
Remediation also involves preventing new growth of molds by amending sources of moisture in a home. Depending on your contamination calculations, you will be able to determine if you are working on level 1 remediation (which is used in small, isolated areas which have mold growth up to 10 feet) or level 2 remediation (which involves 10-30 feet mold coverage). Regardless of the level, mold clean-up process is similar, and it involves the following steps:

a. Repairing water problem – this is important to prevent new mold spores from growing and consequently remedy the problem once and for all.

b. Isolate contaminated areas – isolation for level 1 and two remediations is done by closing all doors and windows between the area contaminated and other rooms in a home. However, for level 2, a six mil polyethylene sheeting is used to cover all doorways and other openings found in the contaminated area. Also, to make sure that the sheeting properly isolates the area, seams are sealed with duct tapes.

c. Suppress the dust – to reduce the amount of dust in the contaminated area; you should sprinkle some water to suppress the dust.

d. Remove materials – after suppressing dust, remove all wet and even mold damaged porous materials found in the contaminated area. If you are not sure which materials you should remove, you can check with your supervisor, refer to the Environmental Protection Agency (EPA) or even Mold Remediation in Schools and Commercial Buildings.

e. Place the materials in plastic bags – all wet and moldy materials should be discarded in in plastic materials which are at least six mils thick. Then, double the bags and tie them tightly to dispose of the materials

f. Clean the area – using a wire brush on moldy surfaces, clean all porous materials and wood surfaces and the wipe the areas with disposable wipes. Also, scrub all moldy surfaces with a damp cloth and a detergent solution until you’ve removed all the mold and then rinse with clean water to removal all spores that may regenerate.
For level 1, you can clean with a damp cloth and mop with a detergent solution, but level 2 requires thorough vacuuming with HEPA vacuum followed by wiping with a damp cloth and/or using a detergent.
g. Carry out visibility tests – all areas should be clean and visibly free from contamination and debris i.e. dirt and molds.

h. Dry your items – allow your materials to dry so that moisture could evaporate to avoid regeneration of molds. To speed up the drying process, you can use fans, raise indoor temperatures or even use dehumidifiers.

i. Carry out replacement – replace all defective materials or the materials which should be replaced.Most builders hire mold remediation firms to clean up homes which have contamination areas exceeding 30 square feet. If any additional mold is discovered during the clean-up process, the warranty supervisor should update the plan to remove mold contamination thoroughly.

Step 5: Determine whether the clean-up process has been successful

Even if the surface appears clean, it is not a guarantee that you are done with molds! You should carry out tests to see whether the clean-up process has been successful. The EPA document, Mould Remediation in Schools and Commercial Buildings offers important guidelines on how you can complete the clean-up process. Some of the guidelines documented include this article:

• Verifying if the moisture problem has been successfully fixed. This can be done by revisiting your home after remediation to see if there are any moisture problems
• Checking for signs visible molds, mold damaged materials or even mold odours
• As a home owner, you should be able to occupy or re-occupy your home without any health complaints related to moulds
• You can carry out additional testing with an environmental testing
company to verify that molds have been removed successfully

With a good management strategy, it is possible to successfully clean-up molds from your home. However, the clean-up must be immediate and thorough by following the steps outlined above. Personal protection is of paramount importance when carrying out the clean-up process to avoid developing health complications. For level 1 and two remediations, you can use an N95 respirator, eye goggles and hand glove that extend to mid fore arm as personal protection equipment.

Finally, assess mold growth situation before you embark on the clean-up process to know how you will go about it. Also, make sure that you’ve all the protective equipment for your personal safety

Sewer Pipe Investigations And The Use Of Robots

Pipelines, sewer lines, and other pipes can find an actual benefit in this non-destructive method of surveying their interior. In most cases, pipes that need to be inspected are underground and can be hard to reach for those who need to make the repairs. By using robots to survey the interior parts of a pipe, they can explore the area with video cameras allowing for a detailed analysis of the damage, leak, or blockage. Robot inspections can reveal many types of issues such as tree roots, broken tiles, faulty mortar connections, inline traps, negative grade sloping, pipe sagging, offset joints, pipe cracks, and buildups from sludge or grease.

Before robots were used to identify problems, sewer projects had to be done with guess work and had to be explored by using less accurate methods such as digging up the perimeter. This can cause more problems than help. With the incorporation of robots and video cameras that have radio transmitters, the area that needs to be repaired can be targeted without mistake. This allows for lower costs and time because of an accurate assessment of the trouble.

A professional operating a Sewer Pipe Inspection Crawler Camera is called to the location with the correct tools to handle the analysis of the situation. Many of these areas are impossible for people to explore. Many pipes in cities and other locations, need repairs due to age. Robots can assist in determining an accurate forecast on what lines should get the most attention. This is valuable information when it comes to planning a budget for a company or government agency.

The conclusion is that robots provide a valuable asset for sewer pipe investigation and the analysis of the possible nature of the damage. A push camera inspection system keep people safe and allow them to complete their work without risk or injury. Robots enable people to avoid unnecessary work and to provide an accurate method of targeting the correct location that needs to be repaired.

How to choose a HVAC contractor

When you need heating, ventilation, and an air conditioning system either installed, repaired, maintained or replaced in your home, you should hire an HVAC contractor. The contractor should be highly experienced, skilled, licensed, insured and with the right certificates which comply with his professional field. Having such kind of a Contractor makes it easy for you’re to work with him while you are still getting quality services worth of the money you are paying.

This article will help you choose the best HVAC contractor to work in your home or your office.

a) Ask for referrals from friends and family

When you talk to your friends or family members who had an AC repair, maintenance or replacement before, you should ask for their comments and reviews of the contractor you want to hire. Since they have had their experience, they can be very helpful in explaining how competent the contractor as well as the kind of services he offers. Additionally, you can still visit certain websites online which has comments, reviews, and ratings of local AC contractors to see the most suitable contractor for the job. Positive reviews, high rating, and good comments show that previous clients were contented with the kind of services they got and most likely you will be satisfied too with what you will get.

b) Check whether your contractor has licenses and certificates required in your local area

Having the right documents displays a high level of professionalism making the contractor legitimate and reliable. If you are not sure of the documents to ask for, you can contact a government official or even a government representative in your area to know what to ask for. Also, you should check the validity of the documents these contractors possess to make sure that they are legitimate.

c) Ask for the current licenses and certifications from your HVAC contractor

Your contractor should have worker’s compensation insurance to make sure that in case he gets injured in your home, you won’t have to pay for his hospital bills. It is, therefore, important to ask for their current licenses and certificates.

d) Choose an insured HVAC contractor

“You can protect your home from damages if your contractor is insured.” Cedric Johnson of Heat Pump Victoria BC. “You are not supposed to take chances when hiring a contractor because it may turn out to be an expensive endeavor if he or she is not insured.”

Therefore, you should check with a consumer affair organization in your locality to see that your contractor has a decent rating and a low volume of customer complaints before hiring their services. For example, a ductwork repair company failed to join a consumer affair organization which led to their company going bankrupt after a number of complaints.

e) Ask the HVAC contractor to give you references of past clients

If you can access the internet, you should check customer testimonials among other types of feedback from previous clients to understand the kind of services the contractor give.

f) Choose a contractor who inspects the system before giving an estimate

A good contractor should look for air leaks, measure the air flow of the unit and inspect the AC unit to make sure that the components meet the guidelines as well as the specifications of the manufacturer. He or she should not give a price quote first without examining the problem and discussing with the owner the possible solutions available.

g) Get at least three biddings from different contractors a Las Vegas air conditioning repair and installation company advised us to do the following: “Getting different bids from different contractors enables you to have a rough idea of the price you are supposed to be charged for the service. Also, the bids might help you consider the most energy efficient plan and the length of warranties offered. Simply, a variety of deals helps one to have the best deal after considering all the available options.”

h) Verify if the contractor will offer you with a written deal or in the form of a contract

Having a written agreement can be helpful if you are having disagreements or the contractor did not complete the work he or she was paid to do. In writing, some of the important details you should include are:
• The dates on which installation, repair, maintenance or replacement will be done
• The cost of all fees included
• Labor to be provided
• Equipment to be used
• Potential future fees which the AC unit might need e.g. upgrades
• Due dates of payments

Following the above tips will make you choose the best HVAC contractor who will help you with any kid of service you need. You should “not do it hurriedly since you may end up choosing the wrong contractor for the job.” says Las Vegas Air Conditioning worker, James Pruitt of Goettl.

Heating Installation

Whenever things start to get a bit cold, we may think about having an efficient heating unit installed in our homes. However, not a lot of people actually follow through on these plans. If you have an existing system, then you may be worried about the cost of upgrading. If your home does not currently have to heat, then you may think that having it installed will be too much regarding effort and money. However, it may actually be more affordable than you would imagine.

If you already have a fixed heating system in your home then can be made of all the existing ducts. This will reduce the costs, and you may be looking at anywhere between $3500 to $4000 depending on the size of your home. The whole project should take no more than three days.

Installing a whole new system will take twice this long, and it will also cost twice as much money. A good installation team can place ducts in discrete locations so that they do not look out of place. The project may not create as much mess in your home while the installation is taking place as you might imagine.

Selecting And Sizing A Unit

If you decide to go ahead with installation, then the first decision that you will have to make will be about which unit to choose. This is a decision that needs to be made carefully because once the unit has been installed, it will be quite expensive to replace.

Fortunately, there is a calculation that contractors can carry out which will let you know that size unit you need. There are many factors that can determine which size unit you need and this calculation will take them all into account. This includes things such as how much insulation you have in your home and which direction your home is facing in correlation to the sun. The calculation that the contractor does can also be quite useful for working out whether you would benefit from extra insulation.

When this calculation has been carried out, then the contractor will make their recommendation. Getting a unit of the right size is very important. If you do not have a unit that is big enough then not will it not be enough to cool a room down completely, you will have to leave it running for longer before you start to notice a difference. A unit that is too big will not reduce the humidity in the room enough because the system will shut down before it has a chance to do this. This means that the room will feel clammy rather than cool.

Every unit will have a seasonal energy efficiency rating or SEER. A higher SEER will mean that the unit is more efficient. Federal law states that the SEER of any new heating unit should be at least 13. You should expect to pay more for a unit with a higher SEER, but there will be benefits such as lower operating costs. These units will be of a higher quality with better sound shields. They are also much safer and use a lower voltage.

Express Plumbing and Heating explicitly said that you will usually have the choice between two different types of unit – a package system or a split system. Package systems are quite rare, but they may still be an option. A package system has all the components of the system within one unit. It is usually mounted on the wall and ducts will need to be installed. Check out some cool furnaces on their Twitter.

If you have a split system, then the condenser will be located on the outside of your property. Pipes will run inside the house and connect to the fan and coil system which can be placed in the attic. The cool air will then be dispersed through the house via the ducts.

Another thing to consider when you are thinking about where to place the heating unit is that they will make quite a bit of noise. Even if it is outside, there is a good chance that you will hear the unit if it is located near a window.

If you already have ducts, then they will need to be inspected to make sure that they are suitable for the heating system that is to be installed. Older ducts tend to be best because they are larger and the air can flow through them better. Some modifications that may need to be made include sealing the ducts so that efficiency increases or upsizing the furnace blower.

If you do not have ducts in the house already, then you will need to have them installed. This is something that the contractor will be able to carry out for you, but they will need plans of your home. This will enable them to plan the best way to get the air from the fan and coil system in the attic to the other rooms in your home.

A good option for getting the duct from the attic to the first floor is to go through the back of closets. The main advantage of this is that is keeps everything concealed so that your home does not look untidy. The ducts take up less space than you might think and therefore you do not have to worry about losing a lot of storage space. You may be offered the choice of a flexible duct of space is a concern but these are not a great choice because they can become worn very easily, and if they get a hole in then they will stop working.

One of the main concerns that people have about having ducts installed in their home is the mess that will be left behind. People sometimes have the idea that a lot of mess will be made because major alterations have to be made to your ceilings, but this is not the case. In most cases, only small holes will need to be created, and this process will not create any mess that can not easily be dealt with.

If you had thought about having heating installed in your home before but never made any serious inquiries, then it might be time to give it some extra thought. It may not cost as much as you would expect and it can make a real difference to the comfort levels in your home in the summer months.